18/april/2012

  1. moved jumper_SMD.sym to obsolete
  2. moved instr_amp_SO8 to obsolete
  3. added instr_amp_8pin -- generic instrumentation amplifier
  4. removed local gafrc from new_geda_project script.
  5. added DIP12.fp DIP14.fp DIP16.fp DIP18.fp DIP20.fp DIP24.fp DIP24_wide.fp DIP40_wide.fp DIP6.fp DIP8.fp

27/march/2012

  1. added dir for obsolete symbols
  2. moved cap_SMD.sym, cap_thru.sym amd cap_SMD_vert.sym to obsolete
  3. added cap_horiz.sym
  4. improved new_geda_project.sh

12/december/2011

  1. added tvs_RM10.fp
  2. a more general symlib path in the gafrc installed by new_geda_project.sh

2/november/2011

  1. renamed HF_MULTI.fp to HF_multi.fp
  2. added opamp_offset2.sym - an opamp with offset at pin 1 and pin 8
  3. more clearance to SCSI footprints

28/sptember/2011

  1. renamed 7474112_2xJK.sym32_4x_OR.sym to 7432_4xOR.sym
  2. renamed 74112_2xJK.sym to 74112_2xJK_flipflop.sym

24/august/2011

  1. add LED_5mm.fp
  2. moved LED_3MM.fp to LED_3mm
  3. moved dio_RM5.pcb to dio.pcb

08/august/2011

  1. add layer_content.sh (cut and paste layer content)
  2. add set_linewidth.sh (manipulate the linewidth of selected tracks)

19/july/2011

  1. add IGBT-symbols: igbt.sym, igbt_diode.sym
  2. add IGBT footprints: TO220_GCE.fp, TO220_GCE_LAY.fp, TO247_GCE_LAY.fp
  3. add IR2110.sym and IR2110S.sym -- low-side/high-side IGBT driver

14/july/2011

  1. beautified opamp symbols
  2. add SCSI_help.fp and SCSI_help2.fp

09/july/2011

  1. renamed pin template symbols, so they don't contain hyphens.
  2. add con_2x10a.sym, same as con_2x10.sym but with alternate pin numbering
  3. unified the power symbols
  4. moved vcc-minus.sym to vee.sym

05/july/2011

  1. beautified in.sym and out.sym and changed device to PORT
  2. add set_net_of_port_symbol.sh

27/june/2011

  1. corrected pad_round.fp and pad_square.fp (wrong side of the board)

20/june/2011

  1. started a page for the essential lib

15/june/2011

  1. added pin_meas.fp pin_0.5mm.fp pad_square.fp pad_round.fp pin_1mm.fp
  2. removed pad_60x60.fp pad_SMD.fp pad_SMD_round.fp
  3. moved PAD.pcb to pad.pcb

3/june/2011

  1. beautified switch symbols. Added symversion attributes, removed numslot attribute, removed device attribute.
  2. swapped pin numbers of dipswitch_4x.sy for compatibility with the other switch symbols

2/june/2011

  1. corrected footprint attribute in several connectors.

31/may/2011

  1. add SO16W.fp, SO20.fp, SO20W.fp, SO24W.fp
  2. typo in set_pinnumber.sh

28/may/2011

  1. more symbol beautification
  2. corrected the default footprint of pmosfet.sym

26/may/2011

  1. filled logic bubbles to beautify digital symbols

13/may/2011

  1. corrected wrong pinout of 78L05_SO8.fp and moved to 78Lxx_SO8.fp
  2. increased annular rings of some TOxxx.fp
  3. add script to set the number_of_pages attribute in schematics

9/may/2011

  1. increased pad size of cap_RM*.fp
  2. add cap_RM5_c.fp -- small outline package
  3. corrected pin numbers of various switches. Increased annular ring, too.

18/april/2011

  1. corrected pinnumbers of header footprints with elongated pads.
  2. add AMP_4.2mm_header_20pin_lay.fp header similar to the ones used for mother boards
  3. improved schaltplandruck --> sort schematics according to page attribute

13/april/2011

  1. minor beautification of comparator_quad_pwr.sym, 7400_4xNAND.sym, analog_switch_DG468.sym
  2. add SCSI_VHDCI_cable_lay.fp

21/march/2011

  1. add versions with oblong pins to the series of footprints for two row headers.

14/march/2011

  1. better clearance of DIOTEC_*.fp

3/march/2011

  1. add SOT886.fp
  2. add RCA_DUAL_CUI_RCJ22.fp
  3. add BNC_DUAL_BOMAR364.fp

1/march/2011

  1. replaced (getenv "PWD") with "." in new_geda_project.sh to make gschem start up properly from nautilus.

21/february/2011

  1. add LM317_SO8.fp variable voltage regulator in SO8 package
  2. add DPAK_GDS.fp DPAK with pins named for power P-MOSFETs like IRL5602
  3. add AMP_4_2mm_header_20pin_lay.fp an ATX like 20 pin power connector
  4. add 2x20PIN_PSL.fp a 40 pin header with interlock mechanism
  5. add 2x4socket.fp eight pin socket with two rows
  6. put changelog in extra page

19/february/2011

  1. improved oblong pads with TO*.fp and SUBD*.fp (mask smaller than polygon clearance)
  2. polished SO14.fp, SO16.fp, SO28W.fp, SO8.fp, SOT363.fp (better mask)
  3. add SO8_FET.fp for power MOSFETs in SO8 design
  4. enlarged annular rings in PENTAWATTV footprints
  5. add convenience script extract_footprints.sh
  6. add convenience script set_name_value_description.sh
  7. add led_bicolor_4pin.sym, a slotted symbol for bicolor LEDs with four pins
  8. add LTST-C155.fp - a footprint for a bicolor SMD LED by LITEON
  9. polished the diodes: triangles more equilatral

8/february/2011

  1. oblong pads and a square No1 pin with TO220**.fp and TO92**.fp
  2. find_missing_symbols.sh

3/february/2011

  1. beautified subD9.sym, subD15.sym, subD25.sym
  2. new subsheet-2.sym, template with pins 400 units apart
  3. add 12V+.sym, 12V-.sym
  4. add supply_with_variable_regulators.sym
  5. shortened the pins of elko.sym to make it compatible with cap_SMD_vert

2/february/2011

  1. add res_zero.sym
  2. reworked subsheet.sym
  3. add footprints and values to dus.sym, comparator_quad.sym
  4. polished 7905.sym

26/january/2011

  1. add con_SMA.sym
  2. fixed license in con_BNC.sym
  3. add footprint list to con_BNC.sym

26/january/2011

  1. add subD15.sym

31/december/2010

  1. corrected URL to SPECTROL_534.fp

12/december/2010

  1. add .gitignore to new_project.sh
  2. polished subsheet.sym
  3. polished pin-*.sym
  4. add subsheet_in_out.sym, a convenience symbol for subsheet generation

8/december/2010

  1. add schaltplandruck.sh, a recursive print script for gschem schematics
  2. add block symbol resistor_dipswitch_beanstalk.sym, a stack of configurable resistors
  3. larger pins at cap_RM275.fp

7/december/2010

  1. polished 74161_COUNTER.sym and moved to 74161_counter.sym
  2. polished 74163_COUNTER_DECIMAL.sym and moved to 74163_counter_decimal.sym
  3. add pin_left.sym, pin_right.sym, pin_top.sym, pin_bottom.sym convenience symbols
  4. add 555.sym and 556.sym, single and dual. general purpose timers.

3/december/2010

  1. add 0805xs.fp extra small pads
  2. move 0805r.fp to 0805s.fp
  3. move 0402r.fp to 0402s.fp
  4. add 0603.fp
  5. beautified dio_1206, fp dio_1210, fp dio_1812.fp, tantal_7x4mm.fp, tvs_1812.fp, 0805.fp, 1206.fp, 1210.fp, SOT89.fp

23/november/2010

  1. add SO8_FET, MOSFET footprint, SO8 style.
  2. add list of footprints to res_thru
  3. moved hole footprints from misc/ to a separate dir
  4. changed default refdes of pad_2.sym to refdes=PAD?

8/november/2010

  1. add SOT89.fp
  2. add TO252.fp, aka DPAK.fp
  3. add footprints list to 7805.sch

1/november/2010

  1. add socketed resistor res_socket.sym, res_socket.fp
  2. clean-up of res_RM**.fp (metric holes, larger annulus, mark at pin 1)
  3. add perfboard.sym
  4. renamed lochraster*.fp to perfboard*.fp

28/october/2010

  1. redefined existing holes and added some more.
  2. add footprint template

26/october/2010

  1. add RIACON_3PIN_LAY.fp and RIACON_2PIN_LAY.fp

16/october/2010

  1. more annulus to SMA_*.fp and BNC_*.fp
  2. more annulus to RIACON_2PIN.fp
  3. add RIACON_3PIN.fp
  4. add HF_MULTI.fp a footprint for various coaxial connectors
  5. renamed TFQP100.fp to ATXMEGA_TFQP100.fp

12/october/2010

  1. add multiplexer_DG406.sym
  2. add 2x13PIN.fp
  3. polished 2x13PIN_WSL.fp

8/october/2010

  1. renamed TFQP100.fp to TQFP100.fp

4/october/2010

  1. add TFQP100.fp

1/october/2010

  1. add mark_2.fp, a square production mark
  2. renamed MARKE.fp to mark_1.fp
  3. fixed usage comment in set_pinnumber.awk
  4. add TO220_block.fp, generic TO220 mounted to a cooling block
  5. add oblong pads to the pins of TO220*.fp
  6. add flag nopaste to oblong pads of TO92*.fp

28/september/2010

  1. add SMA_EDGE.fp, a SMA footprint to be soldered from the edge of the PCB
  2. add cuboid_5x9mm_SMD, a brass cuboid to be soldered to a polygon
  3. add cuboid.sym, a cuboid symbol
  4. add LT1719, a specific comparator

27/september/2010

  1. polished 78L**.sym and 79**.sym
  2. improved supply block and moved to supply_with_regulators.sym

26/september/2010

  1. add EL7222.sym, a line driver
  2. add nc.sym, to mark deliberately not connected pins
  3. add author attribute to 78**.sym and 79**.sym
  4. polished ATmega32TQFP.sym
  5. add ATxmegaA1.sym

23/september/2010

  1. add inductor_vert.sym

22/september/2010

  1. corrected subD25.sym --> shield is pin number 0, rather than 26

11/september/2010

  1. add elko_RM10_D22.fp
  2. moved PS_**PIN_lay.fp to PS_**PIN_LAY.fp
  3. moved SCSI_68pin.fp to SCSI_68pin_vert.fp
  4. larger screw holes in SCSI footprint
  5. bug fix in.sym

3/august/2010

  1. more annular ring in res_RM5.fp and res_RM5_b.fp

2/august/2010

  1. added 2x13PIN_WSL.fp
  2. fixed footprint attribute of nmosfet.sym
  3. added SUBD15_male_lay.fp SUBD25_male_lay.fp SUBD37_male_lay.fp
  4. decorated SUBD*.fp with oval pads for easier soldering

27/july/2010

  1. added TO92 FET footprint with alternative pin allocation, TO92_DGS
  2. added generic TO92 footprint TO92_123.fp
  3. modified TO92* footprints for elongated pads

26/july/2010

  1. bug-fix subD25.sym
  2. added SO28W.fp

13/july/2010

  1. added schalter_1x_mittel.sym switch in middle position
  2. added an outline to lochraster2.pcb
  3. marked pin 1 of res_*.fp with the square flag

5/july/2010

  1. added convenience script set_pinnumber.awk

29/june/2010

  1. embedded components in symbols of the block section.

28/june/2010

  1. removed SCSI footprint SCSI_68pin_female.fp
  2. renamed SCSI_68pin_male.fp to SCSI_68pin.fp
  3. added SCSI_VHDCI_cable.fp
  4. added coded_switch_4bit.sym and ELMA_C08.fp
  5. added subD25.sym

15/june/2010

  1. added SCSI footprint matching footprint SCSI_68pin_female.fp

14/june/2010

  1. added SCSI connector symbol con_SCSI68.sym
  2. moved pins of res_RM??.fp to multiples of 50 mil

31/may/2010

  1. add quad_analog_switch_closed.sym -- an opening analog switch, e.g. DG212.
  2. add res_thru_vert.sym, vertically drawn thru hole resistor.
  3. larger annular rings with 1x1PIN.fp, 1x3PIN.fp, 1x5PIN.fp, 2x3PIN.fp,
  4. beautified con_2x8.sym, con_2x3.sym
  5. correcter pin numbers of con_2x20.sym
  6. added work sheets 1xnPIN.pcb and 2xnPIN.pcb
  7. added 2x2PIN.fp, 2x4PIN.fp, 2x5PIN.fp 2x8PIN.fp
  8. renamed 2x20pin.fp to 2x20PIN.fp
  9. renamed AKL_4Pin.fp to AKL_4PIN.fp
  10. renamed con_2x16-2.sym to con_2x16.sym and larger annular rings.
  11. added con_2x10.sym, con_2x16.sym, con_2x2.sym, con_2x32.sym

26/may/2010

  1. add poti_thru_vert.sym
  2. add trimmers.pcb
  3. corrected default footprint of res_thru.sym
  4. enlarged annular rings of ALPS_RK11K112.fp

25/may/2010

  1. add lochraster2.fp a grid of holes

18/may/2010

  • larger holes in BNC_vert3.fp
  • more clearance to M3_plated.fp

    6/april/2010

    1. add 2x20Pin.fp, 2x5Pin.fp
    2. add AKL_4Pin.fp
    3. add TQFP44.fp, ATmega32TQFP.sym
    4. con_2x16-2.sym, 2x20.sym, con_2x5.sym, con_2x8.sym
    5. crystal.sym

    26/march/2010

    1. improved layoutdruck.sh. Now accepts command line options -p and -V

    20/march/2010

    1. add the pcb print script layoutdruck.sh

    19/march/2010

    1. add max232.sym.

    16/march/2010

  • various bug fixes and typos.

    13/march/2010

    1. fixed typo in description of divider_MC12093.sym
    2. fixed typo in description of comparator_dual_pwr.sym

    24/february/2010

    1. add pin V_L to quad_analog_switch_pwr.sym
    2. install attrib file to the print subdir of the project dir
    3. add a layout print script to new_geda_project.sh
    4. add a bom print script to new_geda_project.sh

    10/february/2010

    1. add tvs_1812.fp
    2. add tvs.sym
    3. rename suppressor_SMD.sym to tvs_vert.sym

    25/november/2009

    1. comparator_dual_pwr.sym: clean-up
    2. mmic-ERA.sym: Only three pins rather than four.
    3. zener_SOT23.sym: corrected an error with pin numbers
    4. symbols/connector/con_XLR3_power.sym

    13/november/2009

    1. add DIOTEC_BXXD.pcb
    2. add elko_BC_D35.fp - high voltage elcap by BC-Components
    3. add TSOP6.fp
    4. add analog_switch_TSOP6_pwr.sym
    5. add analog_switch_DG467.sym and analog_switch_DG468.sym
    6. add analog_switch_TS3157.sym and analog_switch_TS3157_pwr.sym

    3/October/2009

    1. add title-block.sym -- A titleblock without a frame
    2. enhanced the project start script new_geda_project.sh
    3. add SOT343.fp
    4. add mmic-BGA427.sym
    5. cleaned BNC_LAY.fp (footprint format rather than layout format)

    29/September/2009

    1. add zener_SOT23.sch
    2. move zener_SMD.sch to zener_minimelf.sch

    23/September/2009

    1. add quad_analog_switch.sch and corresponding power pin symbol quad_analog_switch_pwr.sym
    2. add pinseq Attributes to instr_amp_*.sym

    17/September/2009

    1. add MINICIRCUITS_MMIC.fp
    2. add divider_MC12093.sym
    3. add phase_detector_MCH12140.sym
    4. add 5V+.sym
    5. cleaned 15V-.sym, 5V+.sym
    6. moved 7414_4xNOT_schmitt_trigger.sym to 7414_6xNOT_schmitt_trigger.sym
    7. add XLR3_silk.fp
    8. add footprint_template.pcb

    14/September/2009

    1. add convinience script for project start-up.
    2. short pins to all the diodes. (yes, this breaks old schematics on load)

    22/August/2009

    1. add SOT363.fp

    10/July/2009

    1. add transformer_3pick-ups.sym
    2. add subD9-2.sym (small version of subD9.sym)

    9/July/2009

    1. add suppressor_SMD.sym
    2. add block opamp_with_booster.sym
    3. polished in.sym (better text alignment)
    4. polished L165-1.sym L165-2.sym, L165_pwr-1.sym
    5. polished opamp_dual.sym opamp_dual_pwr.sym
    6. add SOT223.fp

    3/July/2009

    1. add APMEM TL46.fp, vertical two way switch
    2. add MIYAMA_MS500FPC.fp, slightly larger, vertical two way switch
    3. increaseded annular rings of APEM_5236.fp, APEM_TL46WW.fp, APEM_TL36WW.fp
    4. polished SOT_23***.fp

    1/July/2009

    1. added instr_amp_INA163.sym, a low noise microphone diffamp
    2. added instr_amp_INA163_pwr.sym, power symbol for INA163
    3. moved instr_amp_INA128.sym to instr_amp_SO8.sym
    4. polished SO14.fp, opamp.sym
    5. polished opamp_pwr.sym

    28/June/2009

    1. add symbol bridge_rectifier_SMD.sym
    2. cleaned and polished res_RM20.fp, res_RM15.fp
    3. add res_vert.fp, res_RM75.fp, res_RM10.fp
    4. removed resistor_vertical. fp, resistor_vertical2.fp
    5. add DIOTEC_BXXS.fp, DIOTEC_SXX.fp (SMD bridge rectifiers)
    6. add template.pcb, a template pcb for footprints
    7. add HAMMOND_1590B.fp, HAMMOND_1590G.fp, HAMMOND_1590Y.fp
    8. modified HAMMOND_1590B.fp -- lid, rather than box
    9. enlarged annular rings of APEM_TL36WW.fp, APEM_TL46WW.fp, ELEDIS_2B11.fp, ELEDIS_2B11_LAY.fp, MIYAMA_MS500AVT.fp, MIYAMA_MS500FVT.fp
    10. corrected typo in default footprint pnp.sym
    11. add default footprint in enclosing.sym

    23/June/2009

    1. add footprint RIACON_383_2PIN.fp (RIAconnect, series 383, 2 pin)
    2. add symbol con_RIACON_2pin.sym
    3. polished jumper.sym

    23/June/2009

    1. add footprint BOX_HAMMOND_1590LLB.fp
    2. clean-up of BOX_HAMMOND_1590LB and BOX_HAMMOND_1590Q.fp
    3. removed layer garbage from various hole footprint
    4. add tantal_7x4mm.fp

    20/June/2009

    1. add footprint for SMD inductor FASTRON_PISG.fp

    8/June/2009

    1. clean-up of comparator_quad_b.sym
    2. add comparator_quad_b_pwr.sym

    7/June/2009

    1. hole_1mm.fp, hole_2mm and hole_m2.5.fp were in layout format rather than footprints. Corrected.
    2. corrected the description of various holes in index.html

    05/Nov/2008

    1. fixed the footprint of 2x2 jumper (slightly wrong distance of pins)
    2. increased annular ring of jumper footprints.

    05/Nov/2008

    1. fixed links to quad comparator symbols in index file.

    10/Oct/2008

    1. corrected SMA_LAY.fp and SMA_VERT.fp -- Holes did not fit.

    20/Sept/2008

    1. add SCSI_68pin_male_vert.fp, recepticle, compatible with national instruments cards
    2. add lochraster.fp, 100 mil prototype board

    8/Sept/2008

    1. add MIYAMA_MS500FVT.fp, 2 way switch, vertical pcb mount
    2. add MIYAMA_MS500FVT.fp, 1 way switch, vertical pcb mount

    5/Sept/2008

    1. add XLR3_PCB, an pcb mounted version of the XLR connector by NEUTRIK
    2. modified the XLR footprints so that the included jae connectors will receive positive voltage at the red cable.

    29/Aug/2008

    1. add female SubD9 connector footprints --> SUBD9_female_lay.fp and SUBD9_female_vert.fp
    2. Renamed male SubD9 connector footprints
    3. Corrected the pin numbers of SOT23_SDG
    4. connector symbols PS_*: changed device attributes to value attributes
    5. increased holes of ALPS_RK11K112.fp

    19/Aug/2008

    1. corrected VISHAY_RH10.fp (mirror, placement of holes)
    2. changed supply_with_virtual_GND.sym (Schottky diode rather tham DUS)

    14/Aug/2008

    1. corrected SOT23 confusion (hopefully).
    2. add dio_1812.fp
    3. add elko_RM35_D8.fp

    6/Aug/2008

    1. fixed the link to Resistor_thru_vertical2.fp
    2. add JMP_default.fp -- A footprint to mark the default setting of a jumper

    12/July/2008

    1. add 0805r.fp
    2. add con_4x_shield.sym, shielded four way connector

    12/July/2008

    1. add regulators 78*.sym, 78L*.sym, 79*.sym and 79L*.sym
    2. add 0402.fp and 0402r.fp

    12/July/2008

    1. add SMA_LAY.fp -- SMA recepticle, telegärtner J01151A0191
    2. add SMA_VERT.fp -- SMA recepticle, telegärtner J01151A0931
    3. add BNC_VERT3.fp -- BNC recepticle, telegärtner J01001A1945 or J01001A1944
    4. moved BNC_STAND.fp to BNC_VERT.fp
    5. moved BNC_STAND2.fp to BNC_VERT2.fp
    6. clean-up of BNC footprints
    7. add LEMO_4PIN.fp -- recepticle, LEMO EPG.0B.304.HLN
    8. moved PS_*PIN_gerade.fp to PS_*PIN.fp
    9. moved PS_*PIN_winkel.fp to PS_*PIN_LAY.fp
    10. add 1x4PIN.fp, PS_4PIN.fp and PS_4PIN_LAY.fp
    11. changed the text default position of PS_*.fp footprints and JMP_*.fp
    12. add JMP_3PIN_SMD.fp
    13. add jumper_2x2.sym

    10/July/2008

    1. add REF02.sym, a precision voltage refernce with temperature transducer
    2. add dipswitch_4x.sym

    8/July/2008

    1. add TO220_bighole.fp, to mount a voltage refernce as low as posssible.
    2. add Vishay_PH1.fp, a popular power resistor
    3. corrected jumper.sym (gschem choked on it because of a missing parameter)

    2/July/2008

    1. corrected TO247.fp (was falsely assumed to be similar to TO220)
    2. add TO247_2.fp (large holes to completely sink the pins)
    3. add TO247_LAY.fp (heatsink on pcb)
    4. changed the generic footprints TOxxx.fp -- more polygon and mask clearance

    26/June/2008

    1. corrected the outline of SPECTROL_534.fp

    23/June/2008

    1. add block supply_with_virtual_GND.sym
    2. larger pads for FASTRON_PISR.fp
    3. add symbol poti_Spectrol_534.sym and SPECTROL_534.fp

    6/June/2008

    1. add schalter_2x_um.sym, DPDT switch
    2. add APEM_TL46WW, DPDT switch
    3. rename MULTICOMP_AS to APEM_TL36WW

    4/June/2008

    1. add footprint XLR3_vert.fp for vertically mounted XLR recepticle
    2. add generic footprint SOT23.fp
    3. add block supply_with_virtual_GND.sym

    26/May/2008

    1. add PS-8.sym, PS-5.sym, PS-3.sym, PS-2.sym -- JAE connectors, series IL-G, sold bei Reichelt.
    2. add con_pm_Ub.sym -- a connector dedicated to distribute power among boards.
    3. update to block XLR-78xx-79xx.sym
    4. add BNC_STAND2.fp -- model telegärtner J01001A0037, to be mounted vertically
    5. add BNC_SAND3.fp -- model telegärtner J01001A1945, vertical full metal recepticle

    19/May/2008

    1. more telling names for digital 74xxx symbols.
    2. new symbols 7400_4xNAND.sym, 7402_4xNOR.sym, 7432_4x_OR.sym
    3. removed 74128.sym - This component is depreciated

    9/May/2008

    1. Moved opamp_*_2.sym to opamp_*.sym. I decided, not to put version strings in the name of a symbol. Components should be embedded, when a a schematic is regarded as finished.
    2. new symbol 7414.sym (6xNOT)
    3. shorter pins to led_3mm.sym --> Note, this breaks existing schematics.
    4. clean-up license of relay-AXICON_FP2.sym
    5. add symbol flyback_SOT23.sym (A pair of schottky diodes for flyback protection)

    7/May/2008

    1. Shorter pins in comparator_quad.sym and comparator_quad_b.sym.
    2. Short pin versions of opamp.sym, opamp_quad.sym and opamp_offset.sym. These are called opamp_2.sym, opamp_quad_2.sym and opamp_offset_2.sym.
    3. New directory "old" with the long pin versions of opamps and comparators, so old schematics still find them.

    7/May/2008

    Shorter pins in comparator_dual.sym and opamp_dual.sym,to allow for more flexibility in schematics. Note: This likely breaks schematics, that use the previous version.

    28/Apr/2008

    1. increased polygon clearence of a couple of SMD components. Now, polygon clearence is twice the size of solder mask clearence.
    2. increased mask clearence of cap_RM5.fp, cap_RM275.fp, res_RM20.fp and JMP_*Pin.fp
    3. decreased mask clearence of

    19/Apr/2008

    1. unified and corrected diode footprints (dio_1206.fp and dio_1210.fp)
    2. removed footprint dio_0805.fp
    3. add zener_SMD.sym
    4. add diodes to symbol index
    5. unified pin numbers and pin labels of diodes.

    7/Apr/2008

    1. renamed 0805_dio.fp to dio_0805.fp to conform with the names of the other footprints
    2. correctetd the silk of dio_1210.fp and dio_1206.fp

    4/Apr/2008

    1. clean-up and update of TOxxx footprints: Centroid in the center, named pins
    2. add worksheet TOXXX.pcb

    1/Apr/2008

    1/Apr/2008

    * clean-up and update of 74xxx symbols
    * add footprint for 19" box: BOX_DAUB_MGF44061.fp * add worksheet for boxes made by Daub: BOX_DAUB.pcb * removed multiple GND pins in 78L12.sym and 78L15.sym
    * Graphics polishing 7805.sym, 7812.sym, 7815.sym, 7905.sym, 7912.sym, 7915.sym

    31/Mar/2008

    1. new symbols for generic quad opamp and for quad comparator
    2. centered handle of 0805.fp
    3. larger pads and centered handle for 1206.fp
    4. larger pads and centered handle for 1812.fp
    5. new footprint dio_1206.fp
    6. removed redundant 74_16pin_pwr.sym
    7. graphical improvements to *_pwr.sym
    8. new footprints 1210.fp and dio_1210.fp
    9. new symbol comparator_quad_b.sym for alternative opin-out

    19/Mar/2008

    * new footprints ELEDIS_2B11, ELEDIS_2B11_LAY and MULTICOMP_2AS for small switches
    * added a pcb working sheet for all the switches (switch.pcb)

    13/Mar/2008

    fixed 78L05 and 79L05: dedicated footprint instead of coinciding pins.

    6/Mar/2008

    Another clean-up. Added dist-licence and use-license attributes to the following files:
    L165-2.sym L165_pwr-1.sym LM317.sym LM337.sym lm399.sym njfet.sym nmosfet.sym nmosfet_power.sym npn.sym opamp_dual_pwr.sym opamp_offset.sym opamp_pwr.sym phase_detector_HMC439QS16G.sym pmosfet.sym pmosfet_power.sym pnp.sym poti_Alps_RK11K112.sym poti_thru.sym res0805.sym res_SMD.sym res_SMD_vert.sym res_ref.sym res_thru.sym

    removed LM137 (typo of "LM317")

    5/Mar/2008

    * modified opamp_pwr, opamp.sym --> Add license
    * modified 7805 --> Add pinlabel and pinname attributes
    * modified 78L05 --> correct foot print (SO8)
    * added 78L15, 78L12
    * modified comparator*.sym --> spurious slot defs
    * modified instr_amp_INA128.sym --> off grid pins, general clean-up, pins moved (!)
    * modified L165-1.sym --> general cleanup, pins moved (!)
    * modiified L165-2.sym --> corrected footprint value
    * removed lm311_orig.sym
    * modified ntc.sym --> clean-up

    25/Feb/2008

    * modified XLR-78xx-79xx.sym --> Add safety diodes
    * added BNC_LAY2.fp --> like BNC_LAY but van be mounted vertically too
    * added BNC_STAND.fp --> Telegärtner socket to be mounted vertically

    Jan/2008

    * corrected RELAY_FP2.fp